Differences between revisions 14 and 15
Revision 14 as of 2021-02-06 10:54:59
Size: 7678
Editor: RudolfReuter
Comment: added Mantelwellen Sperre
Revision 15 as of 2021-02-06 11:07:41
Size: 7499
Editor: RudolfReuter
Comment:
Deletions are marked like this. Additions are marked like this.
Line 48: Line 48:
 * '''Coax cable''' HSR195 (VF=0.8), 17 m long, [[https://www.dx-wire.de/hsr195-low-loss-koaxkabel-50.html|www.dx-wire.de]]
 * [[https://en.wikipedia.org/wiki/Sheath_current|sheath current filter]], Ferroxcube CST9.5/5.1/15-3S4, 20 pieces [[https://www.dx-wire.de/ferriteringkerne/ferrite-fuer-mantelwellensperren/cst955115-3s4-ferroxcube.html|www.dx-wire.de]]
 * '''Heat-shrink tubing''', 1:2 (diameter 19 mm to 9,5 mm), 1 m long [[https://www.dx-wire.de/schrumpfschlauch/schrumpfschlauch-12-19mm-auf-95mm.html|www.dx-wire.de]]
 * '''Coax cable''' HSR195 (VF=0.8), 17 m long, see [[WindomAntennaFD4#Links|Links #6]]
 * [[https://en.wikipedia.org/wiki/Sheath_current|sheath current filter]], Ferroxcube CST9.5/5.1/15-3S4, 15 pieces, see [[WindomAntennaFD4#Links|Links #4]]
 * '''Heat-shrink tubing''', 1:2 (diameter 19 mm to 9,5 mm), 0.5 m long , see [[WindomAntennaFD4#Links|Links #5]].
Line 211: Line 211:
 1. [[http://www.dx-wire.de/schrumpfschlauch/schrumpschlauch-12-95mm-auf-45mm.html|Schrumpfschlauch 1:2 (9,5 mm auf 4, 5mm), heat shrink tube]]  1. [[https://www.dx-wire.de/schrumpfschlauch/schrumpfschlauch-12-19mm-auf-95mm.html|heat shrink tube 1:2 diameter 19 mm to 9,5 mm)]]

/!\ Vorläufig / Preliminary, work in progress /!\

Translate (Übersetzte) with Google

attachment:Windom-FD4_Aufbau.png

.

.

.

.

attachment:Windom_Balun_DSC07756.jpg

.

.

Windom Antenna Fritzel FD4

This web page documents the commercial Windom Antenna Fritzel FD4 measured with the Vector Antenna Analyzer FA-VA5.

On the right side you see a picture of the balun of my Windom-antenna.

One source of buying shows Links #1

If you click on a picture it will be expanded. You can go back to the web page with the back arrow of your web browser.

Technical Data

  • Frequency range RX and TX: 80m/40/20m/17m/12m/10m
  • Frequency range RX only: ca. 100 kHz to 30 MHz
  • max. Transmit Power: 0,2 / 0,3 KW
  • Antenna impedance: 50 Ohm (at Balun)
  • Antenna connector: PL-plug
  • Length: 1x 27,6 m and 1x 13,8 m
  • Weight: 1,4 Kg
  • Balun Type: 1:6 AMA
  • Coax cable HSR195 (VF=0.8), 17 m long, see Links #6

  • sheath current filter, Ferroxcube CST9.5/5.1/15-3S4, 15 pieces, see Links #4

  • Heat-shrink tubing, 1:2 (diameter 19 mm to 9,5 mm), 0.5 m long , see Links #5.

attachment:MFJ-941B_DSC05760.jpg

Match Box

Without Matchbox it is not possible to get a good SWR on the 15 m band.

On the 80 m band the bandwith with a good SWR is very narrow. So, a Matchbox is needed.

I am using an old MFJ-941B for tuning and power display.

attachment:Windom_common_Mode_choke_DSC07755.jpg

Common Mode Choke

As recommended in an ARRL paper about Windom antenna I inserted a 30 cm long common mode choke (15 x 2 cm Ferrite rings Links #4) 6.7 m below the Balun, see the picture on the right. In order to keep the rings on place, they are covered by a black heat shrink tube, see Links #5.

The common mode choke will help to keep the RF (Radio Frequency) out of the shack, see Links #2,3.

The 6.7 m length coax cable HSR195 (Links #6) should help to improve the horizontal radiation in the way to fill the deep nulls.

.

attachment:VA5-Windom_MFJ941B_3.7MHz_T3.5_I-H_A0.0.png

FA-VA5 Charts

With my new Vector Antenna Analyzer FA-VA5 I could see very good, how the matching to 50 Ohm is.

On the 80 m band the bandwith of a good SWR (1:1.04) is very narrow, see the chart on the right side.

So, every 50 KHz deviation needs a different tuning.

The actual tuning setup is in the chart comment:

  • T3.5 means Transmitter capacitor set to 3.5.

  • I-H means set Inductance switch to postition H.

  • A0.0 means set Antenna capacitor to 0.0.

The software VNWA is master calibrated, you can see it in the lower left corner of the diagram with letters MC.

attachment:VA5-Windom_MFJ941B_7.05MHz_T5.1_I-G_A5.1.png

Because the 40 m Band is very small (100 KHz), one tuning setup is sufficient.

The center SWR is 1:1.2.

The smith chart or Smith-Diagramm red curve shows the matching.

The blue curve shows the impedance.

The green curve shows the SWR (Standing Wave Ratio).

.

.

.

.

.

.

.

.

attachment:VA5-Windom_MFJ941B_14.2MHz_T5.8_I-D_A7.0.png

The bandwidth on the 20 m band is wide, one tuning setup is sufficient.

The center SWR is 1:1.4.

.

.

.

.

.

.

.

.

.

.

.

.

attachment:VA5-Windom_MFJ941B_21.2MHz_T5.2_I-B_A3.0.png

The bandwidth on the 15 m band is wide, one tuning setup is sufficient.

The center SWR is 1:1.10.

.

.

.

.

.

.

.

.

.

.

.

.

attachment:VA5-Windom_MFJ941B_28.5MHz_T4.5_I-B_A0.0.png

The bandwidth on the 10 m band is wide, one tuning setup is sufficient.

The center SWR is 1:1.21.

.

.

.

.

.

.

.

.

.

.

.

  1. Fritzel Windom FD-4 Antenne

  2. common mode choke explained

  3. Coax Feed Line Common Mode Chokes

  4. Ferrit ring LFB095051-000 Laird

  5. heat shrink tube 1:2 diameter 19 mm to 9,5 mm)

  6. HSR195 coax cable, loss @ 30 MHz: 6,5 dB / 100 m

up to top

Contact Email, please enter your Email address

/!\ The entered Email address will not be published, or given away.

Comment this page
Name:
Comment:
Are you human?

List of pages in this category:

-- RudolfReuter 2019-01-12 11:37:48


Go back to CategoryAmateurRadio or FrontPage

WindomAntennaFD4 (last edited 2021-02-06 11:07:41 by RudolfReuter)